Indesit Washer Dryer WIA 111 User Manual

Instructions for use  
WASHING MACHINE  
Contents  
GB  
Installation, 2-3-4-5  
Unpacking and levelling, 2  
Electric and water connections, 2-3  
The first wash cycle, 4  
GB  
English,1  
Technical details, 5  
Washing machine description, 6-7  
Control panel, 6  
Leds, 7  
Starting and Programmes, 8  
Briefly: how to start a programme, 8  
Programme table, 8  
Personalisations, 9  
Setting the temperature, 9  
Functions, 9  
WIA 111  
Detergents and laundry, 10  
Detergent dispenser, 10  
Preparing your laundry, 10  
Special items, 10  
Precautions and advice, 11  
General safety, 11  
Disposal, 11  
Saving energy and respecting the environment, 11  
Care and maintenance, 12  
Cutting off the water or electricity supply, 12  
Cleaning your appliance, 12  
Cleaning the detergent dispenser, 12  
Caring for your appliance door and drum, 12  
Cleaning the pump, 12  
Checking the water inlet hose, 12  
Troubleshooting, 13  
Service, 14  
Before calling for Assistance, 14  
1
 
Connecting the drain hose  
• the supply voltage is included within the values i  
ndicated on the Technical details table  
(see page 5);  
GB  
Connect the drain hose,  
without bending it, to a  
draining duct or a wall  
drain situated between  
65 and 100 cm from  
the floor;  
• the socket is compatible with the washing  
machine's plug. If this is not the case, replace  
the socket or the plug.  
65 - 100 cm  
Your appliance is now supplied with a 13 amp fused  
plug it can be plugged into a 13 amp socket for  
immediate use. Before using the appliance please  
read the instructions below.  
The drain hose may be  
connected to an  
WARNING - THIS APPLIANCE MUST BE EARTHED.  
THE FOLLOWING OPERATIONS SHOULD BE  
CARRIED OUT BY A QUALIFIED ELECTRICIAN.  
under-sink trap. Before  
connecting the drain  
hose from the machine  
ensure that any blanks  
or removable ends  
have been taken off  
the spigot.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA  
approved fuse to BS 1362 should always be used,  
and the fuse cover re-fitted. If the fuse cover is lost,  
the plug must not be used until a replacement is  
obtained.  
Where it connects  
to the waste water  
pipe cut end off  
spigot or remove the  
blanking cap  
Replacement fuse covers:  
If it is place over the  
edge of a basin or sink  
be sure the free end of  
the hose should not be  
underwater.  
If a replacement fuse cover is fitted, it must be of  
the correct colour as indicated by the coloured  
marking or the colour that is embossed in words on  
the base of the plug. Replacements can be obtained  
directly from your nearest Service Depot.  
Removing the plug:  
If your appliance has a non-rewireable moulded plug  
and you should wish to re-route the mains cable  
through partitions, units etc., please ensure that  
either:  
! We advise against the use of hose extensions; in  
case of absolute need, the extension must have the  
same diameter as the original hose and must not  
exceed 150 cm in length.  
the plug is replaced by a fused 13 ampere re-  
wearable plug bearing the BSI mark of approval.  
or:  
the mains cable is wired directly into a 13 amp cable  
outlet, controlled by a switch, (in compliance with  
BS 5733) which is accessible without moving the  
appliance.  
Ensure that if the drain hose is pushed into a  
standpipe, that the end does not go down more  
than 15cms (6 inches). If the hose is pushed down  
too far, this may cause the machine to self -syphon  
ie. continuously empty as it is filling.  
Disposing of the plug:  
Ensure that before disposing of the plug itself, you  
make the pins unusable so that it cannot be  
accidentally inserted into a socket.  
Electric connection  
Before plugging the appliance into the mains  
socket, make sure that:  
Instructions for connecting cable to an alternative plug:  
Important: the wires in the mains lead are coloured  
in accordance with the following code:  
Green & Yellow Earth  
• the socket is earthed and in compliance with the  
applicable law;  
Blue  
Neutral  
Live  
• the socket is able to sustain the appliance's  
maximum power load indicated in the Technical  
details table (see page 5);  
Brown  
3
 
As the colours of the wires in the lead may not  
correspond with the coloured markings identifyng  
the terminals in your plug, proceed as follows:  
Connect Green & Yellow wire to terminal marked E  
Warning! The company denies all liability if and when  
these norms are not respected.  
GB  
The first wash cycle  
or  
or coloured Green or Green & Yellow.  
Connect Brown wire to terminal marked L or  
coloured Red.  
Once the appliance has been installed, and before  
you use it for the first time, run a wash cycle with  
detergent and no laundry, setting the 90°C  
programme without a pre-wash cycle.  
Connect Blue wire to terminal marked N or coloured  
Black.  
If a 13 amp plug (BS 1363) is used it must be fitted  
with a  
13 amp fuse, either in the plug or adaptor or at the  
distribution board.  
If you are in any doubt the electrical supply to your  
machine, consult a qualified electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in  
accordance with the following code:  
BLUE  
NEUTRAL (N)  
LIVE (L)  
BROWN  
GREEN & YELLOW  
EARTH (E)  
Disposing of the appliance:  
When disposing of the appliance please remove the  
plug by cutting the mains cable as close as possible  
to the plug body and dispose of it as described  
above.  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
CROSS-BAR  
CORD GRIP  
BLUE  
! The washing machine should not be installed in an  
outdoor environment, not even when the area is  
sheltered, because it may be very dangerous to  
leave it exposed to rain and thunderstorms.  
! When the washing machine is installed, the mains  
socket must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent or  
dangerously compressed.  
! The power supply cable must only be replaced by  
an authorised serviceman.  
4
 
GB  
Technical details  
Model  
WIA 111  
59.5 cm wide  
85 cm high  
Dimensions  
Capacity  
52,5 cm deep  
from 1 to 5 kg  
Electric  
voltage 230/240 Volts 50 Hz  
connections  
maximum absorbed power 2050 W  
maximum pressure 1 MPa (10 bar)  
minimum pressure 0.05 MPa (0.5 bar)  
drum capacity 46 litres  
Water  
connections  
Spin speed  
up to 1100 rpm  
Control  
programmes  
according to  
IEC456 directive  
programme 3; temperature 60°C;  
run with a load of 5 kg.  
This appliance is compliant with the  
following European Community  
Directives:  
- 73/23/CEE of 19/02/73 (Low  
Voltage) and subsequent amendments  
- 89/336/CEE of 03/05/89  
(Electromagnetic Compatibility) and  
subsequent amendments  
- 2002/96/CE  
5
 
Washing machine description  
FUNCTION  
Buttons  
Control panel  
GB  
START/  
DOOR PAUSE  
LOCK Button  
Led  
PROGRAMME/  
ON-OFF  
Knob  
Detergent dispenser  
Leds  
TEMPERATURE  
Knob  
Detergent dispenser: to add detergent and fabric  
softener (see page 10).  
START/PAUSE button: starts or temporarily  
interrupts programmes.  
N.B.: once the programme has started, pressing this  
button will stop the cycle and only the LED for the  
cycle phase in progress will light up. After about 1  
minute you will be able to open the door (when the  
DOOR LOCK led switches off). If the DOOR LOCK  
led stays lit, it means that there is something that  
needs to be checked before the door is opened  
(e.g.: there is water in the tub or the temperature of  
the water is too high).  
LEDS: to find out the wash cycle progress.  
FUNCTION buttons: to select the functions  
available. The button corresponding to the function  
selected will remain on.  
TEMPERATURE knob: to set the temperature or  
the cold wash cycle (see page 9).  
Pressing the button again restarts the programme  
from the point at which it was interrupted.  
DOOR LOCK Led: to find out whether the washing  
machine is on and if the appliance door can be  
opened (see page 7).  
PROGRAMME/ON-OFF knob: sets the desired  
programme (see page 8) and switches the machine  
on or off.  
The knob stays still during the cycle.  
6
 
Leds  
GB  
The LEDS provide important information.  
This is what they can tell you:  
Cycle progress:  
During the wash cycle, the LEDs gradually illuminate  
on to indicate the cycle progress:  
Prewash/Wash  
Rinse  
Spin cycle  
Note: during draining, the LED corresponding to the  
Spin cycle phase will be turned on.  
Function buttons  
The FUNCTION BUTTONS also act like LEDS.  
When a function is selected, the corresponding  
button is illuminated.  
If the function selected is incompatible with the  
programme set, the button will flash and the  
function will not be enabled.  
If you set a function that is incompatible with  
another function you selected previously, only the  
last one selected will be enabled.  
DOOR LOCK led:  
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damages,  
wait for the LED to flash before you open the appliance door.  
! The rapid flashing of the DOOR LOCK Led together with the flashing of at least one other LED indicates there is  
an abnormality (see page 13).  
7
 
Starting and Programmes  
If you want to cancel the cycle set, turn the  
PROGRAMME/ON-OFF knob to the position  
and wait for all the LEDs to illuminate and then  
turn off again.  
Briefly: starting a programme  
GB  
1. Switch on the washing machine by turning the  
PROGRAMME/ON-OFF knob to the desired  
programme.  
All the LEDS will light up for a few seconds and  
the DOOR LOCK Led will begin to flash.  
2. Load your laundry into the washing machine and  
shut the appliance door.  
3. Set the wash temperature (see page 9).  
4. Add the detergent and any fabric softener  
(see page 10).  
5. Start he programme by pressing the START/PAUSE  
button for one second.  
If another programme is not selected, the DOOR  
LOCK led will remain lit for about 1 minute.  
6. When the programme is finished, the DOOR  
LOCK Led will flash to indicate that the  
appliance door can be opened. Take out your  
laundry and leave the appliance door ajar to allow  
the drum to dry thoroughly.  
Switch the washing machine off by turning the  
PROGRAMME/ON-OFF knob to the  
position.  
Programme table  
Cycle  
length  
(minutes)  
Detergent  
Program- Wash  
mes  
Fabric  
softener  
Type of fabric and degree of soil  
Description of wash cycle  
temperat.  
Pre-  
wash  
Wash  
Cotton  
Extremely soiled whites  
(sheets, tablecloths, etc.)  
Pre-wash, wash cycle, rinse cycles,  
intermediate and final spin cycles  
1
2
3
4
160  
143  
127  
85  
Max  
Max  
Extremely soiled whites  
(sheets, tablecloths, etc.)  
Wash cycle, rinse cycles, intermediate  
and final spin cycles  
Heavily soiled whites and fast  
colours  
Wash cycle, rinse cycles, intermediate  
and final spin cycles  
60°C  
40°C  
Slightly soiled whites and delicate  
colours (shirts, jumpers, etc.)  
Wash cycle, rinse cycles, intermediate  
and final spin cycles  
Synthetics  
Heavily soiled fast colours  
(baby linen, etc.)  
Wash cycle, rinse cycles, anti-crease or  
delicate spin cycle  
5
6
7
8
92  
86  
76  
30  
60°C  
50°C  
40°C  
30°C  
Heavily soiled fast colours  
(baby linen, etc.)  
Wash cycle, rinse cycles, anti-crease or  
delicate spin cycle  
Delicate colours (all types of  
slightly soiled garments)  
Wash cycle, rinse cycles, anti-crease or  
delicate spin cycle  
Delicate colours (all types of  
slightly soiled garments)  
Wash cycle, rinse cycles and delicate  
spin cycle  
Delicates  
Wash cycle, rinse cycles, anti-crease  
and delicate spin cycle  
Wool  
9
40°C  
30°C  
50  
52  
Very delicate fabrics  
(curtains, silk, viscose, etc.)  
Wash cycle, rinse cycles, anti-crease or  
draining cycle  
10  
PARTIAL PROGRAMMES  
Rinse  
Rinse cycles and spin cycle  
Rinse cycles, anti-crease or draining  
Draining and heavy duty spin cycle  
Draining and delicate spin cycle  
Draining  
Light rinse  
Spin  
Light spin  
Drain  
Notes  
For the anti-crease function, please see page 9. The information contained in the table is purely indicative.  
Special programme  
Daily wash (programme 8 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only  
lasts 30 minutes and allows you to save on both time and energy. By setting this programme (8 at 30°C), you can  
wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.  
We recommend the use of liquid detergent.  
8
 
Personalisations  
Setting the temperature  
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 8).  
GB  
The temperature can be lowered, or even set to a cold wash ( ).  
Functions  
To enable a function:  
1. press the button corresponding to the desired function, according to the table below;  
2. the function is enabled when the corresponding button is illuminated.  
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the  
programme set.  
Enabled with  
programmes:  
Function  
Effect  
Comments  
Cuts the duration  
of the wash cycle  
by 30%.  
1, 2, 3, 4,  
5, 6, 7  
Rapid  
wash  
This option  
reduces the  
amount of  
creasing on  
fabrics, making  
them easier to  
iron.  
When this function is set, programmes 5, 6, 7, 9, 10 will end with  
the laundry left to soak (Anti-crease) and the Rinse cycle phase  
5, 6, 7, 9, 10,  
Delicate  
Rinse cycle.  
LED  
- to conclude the cycle, press the START/PAUSE button;  
- to run the draining cycle alone, set the knob to the relative  
symbol and press the START/PAUSE button.  
will flash.  
Anti-  
crease  
! The machine has an intelligent built in check for out of balance loads. To let protect your machine it may reduce the  
final spin speed if an unbalanced load is detected.  
9
 
Detergents and laundry  
Detergent dispenser  
Special items  
GB  
Good washing results also depend on the correct  
dose of detergent: adding too much detergent won't  
necessarily make for a more efficient wash, and may  
in fact cause build up on the interior of your  
Curtains: fold curtains and place them in a pillow  
case or mesh bag. Wash them separately without  
exceeding half the appliance load. Use programme  
10 which excludes the spin cycle automatically.  
Quilted coats and windbreakers: if they are  
padded with goose or duck down, they can be  
machine-washed. Turn the garments inside out and  
load a maximum of 2-3 kg, repeating the rinse cycle  
once or twice and using the delicate spin cycle.  
Trainers: remove any mud. They can be washed  
together with jeans and other tough garments, but  
not with whites.  
appliance and even pollute the environment.  
Open up the detergent  
dispenser and pour in  
the detergent and fabric  
softener, as follows.  
3
2
1
Wool: for best results, use a specific detergent,  
taking care not to exceed a load of 1 kg.  
compartment 1: Detergent for pre-wash  
(powder)  
compartment 2: Detergent for the wash cycle  
(powder or liquid)  
Liquid detergent should only be poured in  
immediately prior to the wash cycle start.  
compartment 3: Additives (fabric softeners, etc.)  
The fabric softener should not overflow from the grid.  
! Do not use hand wash detergent because it may  
form too much foam.  
Preparing your laundry  
• Divide your laundry according to:  
- the type of fabric/the symbol on the label.  
- the colours: separate coloured garments from  
whites.  
• Empty all pockets and check for loose buttons.  
• Do not exceed the weight limits stated below,  
which refer to the weight when dry:  
Sturdy fabrics: max 5 kg  
Synthetic fabrics: max 2.5 kg  
Delicate fabrics: max 2 kg  
Wool: max 1 kg  
How much does your laundry weigh?  
1 sheet 400-500 g  
1 pillow case 150-200 g  
1 tablecloth 400-500 g  
1 bathrobe 900-1,200 g  
1 towel 150-250 g  
10  
 
Precautions and advice  
! The washing machine was designed and built in  
compliance with the applicable international safety  
regulations. The following information is provided for  
your safety and should consequently be read carefully.  
The crossed out "wheeled bin" symbol on the  
product reminds you of your obligation, that when  
you dispose of the appliance it must be separately  
collected.  
GB  
Consumers should contact their local authority or  
retailer for information concerning the correct  
disposal of their old appliance.  
General safety  
• This appliance has been designed for non-  
professional, household use and its functions must  
not be changed.  
Saving energy and respecting the  
environment  
• This washing machine should only be used by  
adults and in accordance with the instructions  
provided in this manual.  
Environmentally-friendly technology  
If you only see a little water through your appliance  
door, this is because thanks to the latest Indesit  
technology, your washing machine only needs less  
than half the amount of water to get the best results:  
an objective reached to respect the environment.  
• Never touch the washing machine when barefoot  
or with wet or damp hands or feet.  
• Do not pull on the power supply cable to unplug  
the appliance from the electricity socket. Pull the  
plug out yourself.  
Saving on detergent, water,  
• Do not open the detergent dispenser while the  
appliance is in operation.  
energy and time  
To avoid wasting resources, the washing machine  
should be used with a full load. A full load instead of  
two half loads allows you to save up to 50% on energy.  
• Do not touch the drain water as it could reach  
very high temperatures.  
• Never force the washing machine door: this could  
damage the safety lock mechanism designed to  
prevent any accidental openings.  
• The pre-wash cycle is only necessary on  
extremely soiled garments. Avoiding it will save on  
detergent, time, water and between 5 and 15%  
energy.  
• In the event of a malfunction, do not under any  
circumstances touch internal parts in order to  
attempt repairs.  
• Treating stains with a stain remover or leaving them  
to soak before washing will cut down the need to  
wash them at high temperatures. A programme at  
60°C instead of 90°C or one at 40°C instead of  
60°C will save up to 50% on energy.  
• Always keep children well away from the  
appliance while in operation.  
• The appliance door tends to get quite hot during  
the wash cycle.  
• Use the correct quantity of detergent depending  
on the water hardness, how soiled the garments  
are and the amount of laundry you have, to avoid  
wastage and to protect the environment: despite  
being biodegradable, detergents do contain  
ingredients that alter the natural balance of the  
environment. In addition, avoid using fabric  
softener as much as possible.  
• Should it have to be moved, proceed with the  
help of two or three people and handle it with the  
utmost care. Never try to do this alone, because  
the appliance is very heavy.  
• Before loading your laundry into the washing  
machine, make sure the drum is empty.  
• If you use your washing machine from late in the  
afternoon until the early hours of the morning, you  
will help reduce the electricity board's peak load.  
Disposal  
• Disposing of the packaging material:  
observe local regulations, so the packaging can  
be re-used.  
• If your laundry has to be dried in a tumble dryer,  
select a high spin speed. Having the least water  
possible in your laundry will save you time and  
energy in the drying process.  
• The European Directive 2002/96/EC on Waste  
Electrical and Electronic Equipment, requires that  
old household electrical appliances must not be  
disposed of in the normal unsorted municipal waste  
stream. Old appliances must be collected  
separately in order to optimise the recovery and  
recycling of the materials they contain and reduce  
the impact on human health and the environment.  
11  
 
Care and maintenance  
Cutting off the water or electricity  
supply  
Cleaning the pump  
GB  
The washing machine is fitted with a self-cleaning  
pump that does not require any maintenance.  
Sometimes, small items (such as coins or buttons)  
may fall into the pre-chamber that protects the  
pump, situated in the lower part of the same.  
Turn off the water tap after every wash. This will  
limit the wear of your appliance's water system  
and also prevent leaks.  
Unplug your appliance when cleaning it and  
during all maintenance operations.  
! Make sure the wash cycle has ended and unplug  
the appliance.  
Cleaning your appliance  
To access the pre-chamber:  
The exterior and rubber parts of your appliance can  
be cleaned with a soft cloth soaked in lukewarm  
soapy water. Do not use solvents or abrasives.  
1. using a screwdriver,  
remove the cover panel  
on the lower front of the  
washing machine (see  
figure);  
Cleaning the detergent dispenser  
Remove the dispenser  
by pulling it out (see  
figure).  
Wash it under running  
water; this operation  
should be repeated  
frequently.  
2. unscrew the lid  
rotating it anti-  
clockwise (see figure): a  
little water may trickle  
out. This is perfectly  
normal;  
Caring for your appliance door and  
drum  
Always leave the appliance door ajar to prevent  
unpleasant odours from forming.  
3. clean the interior thoroughly;  
4. screw the lid back on;  
5. reposition the panel, making sure the hooks are  
securely in place before you push it onto the  
appliance.  
Checking the water inlet hose  
Check the water inlet hose at least once a year. If  
you see any cracks, replace it immediately: during  
the wash cycles, water pressure is very strong and  
a cracked hose could easily split open.  
! Never use hoses that have already been used.  
12  
 
Troubleshooting  
Your washing machine could fail to work. Before calling for Assistance (see page 14), make sure the problem  
GB  
can't easily be solved by consulting the following list.  
Possible causes/Solution:  
Problem  
• The appliance is not plugged into the socket, or not enough to make contact.  
• There has been a power failure.  
The washing machine won't  
start.  
• The appliance door is not shut properly.  
• The START/PAUSE button has not been pressed.  
NB: It should be held minimum one second.  
• The water tap is not turned on.  
• The water inlet hose is not connected to the tap.  
• The hose is bent.  
The washing machine does not  
fill with water.  
• The water tap is not turned on.  
• There is a water shortage.  
• The water pressure is insufficient.  
• The START/PAUSE button has not been pressed.  
• The drain hose is too low or too far in to the stand pipe (see page 3)  
for correct installation.  
The machine continuously fills  
and empties with water.  
• The wall drainage system doesn't have a standard pipe (min. 38 mm).  
• Some programs have a slower final spin to taked best care of the  
fabrics. See page 8 for details of the final spin speed for each program.  
• The programme does not foresee the draining: some programmes  
require enabling the draining manually (see page 8).  
• The Anti crease finction is enabled: to complete the programme,  
press the START/PAUSE button (see page 9).  
The washing machine does not  
drain or spin.  
• The drain hose is bent (see page 3).  
• Remove the drain hose from the standpipe or under-sink trap and  
check for blockages, ensuring that the water can drain freely away  
from the machine.  
• When the machine is installed, the locking screws for the oscillating  
assembly are still in place. Remove the screws (see page 2).  
• The washing machine is not level (see page 2).  
• The washing machine is closed in between furniture cabinets and  
the wall (see page 2).  
The washing machine vibrates  
too much during the spin cycle.  
• The water inlet hose is not screwed on correctly (see page 2).  
• The detergent dispenser is obstructed (to clean it, see page 12).  
• The drain hose is not secured properly (see page 3).  
The washing machine leaks.  
• This means there is a problem with the machine. Before calling  
Assistance, please follow the set of instructions below:  
1. Switch off the machine;  
The DOOR LOCK Led flashes  
rapidly at the same time as at  
least one other LED.  
2. Remove the plug connecting the appliance to the mains supply  
and wait for at least 40 seconds;  
3. Place the plug back into the socket;  
4. Switch on the machine;  
5. If the problem is still evident after this process has been carried out,  
contact Assistance.  
• The detergent is not suitable for machine washing (it should bear the  
definition "for washing machines" or "hand and machine wash", or the like).  
• You used too much detergent.  
There is too much foam.  
13  
 
Service  
Before calling for Assistance:  
GB  
Check whether you can solve the problem on your own (see page 13);  
Restart the programme to check whether the problem has been solved;  
If this is not the case, contact an authorised Technical Service Centre on the telephone number  
provided on the guarantee certificate.  
! If the machine has been installed or used incorrectly, you may be charged for the maintenance callout  
service.  
! Always request the assistance of authorised servicemen.  
Notify the operator of:  
• the type of problem;  
• the appliance model (Mod.);  
• the serial number (S/N).  
This information can be found on the data plate situated on the rear of the washing machine.  
14  
 
GB  
15  
 
195057565.00  
-
04/2006  
Xerox Business Services  
GB  
16  
 

Infinite Peripherals Universal Remote SCOM 100 User Manual
Ingersoll Rand Marine Radio H2XXXX XXX X User Manual
Init TV Mount 8832 000198 User Manual
Invacare Wheelchair Ranger II250 SERIES User Manual
Jacuzzi Hot Tub EG90 User Manual
JVC Flat Panel Television 1005TNH II IM User Manual
Kenmore Air Conditioner 58072184 User Manual
Kenwood Blender SB050 User Manual
KitchenAid Dishwasher KUDD03DTBL10 User Manual
Kodak Digital Camera 1944685 User Manual