Liebert Computer Drive User Manual
MONITORING  
IntelliSlot USB Card™  
USER MANUAL  
TABLE OF CONTENTS  
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Connect USB Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Configure Power Management for Automated Shutdown. . . . . 3  
PRODUCT WARRANTY REGISTRATION . . . . . . . . . . . . . . . . . . . 6  
i
INTRODUCTION  
Congratulations on your choice of the Liebert Universal Serial Bus  
Adapter Card (P/N#: USBCARD).  
The USB card works with Windows-based PC operating systems.  
By using the built-in Windows Power Management software on Win-  
dows™ 2000/XP platforms, the user can monitor the UPS via the USB  
card.  
Items included with shipment are:  
• Intellislot™ USB card in an antistatic bag  
• User Manual  
• USB cable, 6-foot  
The Intellislot USB card provides one USB port for your Liebert UPS.  
This device is specially designed and tested to function in the Liebert  
Intellislot port of the following supported UPS units:  
• UPStation GXT2U™  
• UPStation GXT™  
• PowerSure Interactive™  
After receiving shipment, please inspect product for any damaged or  
missing parts. If any items are damaged, call Liebert Corporation at  
800-222-5877 and select the Warranty Support option from the menu.  
If components are missing, contact your sales representative for  
replacement.  
NOTE  
The UPS serial communication port (DB-9) is disabled when  
the Intellislot USB card is installed. The Intellislot USB card  
must be removed to enable the DB-9 communication port to  
communicate with other Liebert software or the UPStation  
GXT 2U Configuration Program.  
1
 
INSTALLATION  
Parts required  
• Intellislot USB Card  
• USB cable  
Tools required  
• Either #2 (medium) Phillips or small flat head screw driver.  
1. It is not necessary to turn  
USB card  
being fitted in  
Intellislot Port  
the UPS off prior to instal-  
lation. Locate the Intellis-  
lot Port on the rear panel  
of your UPS. (Location and  
orientation may vary  
according to specific UPS  
model.)  
2. Remove the two retaining  
screws of the Intellislot  
Port cover plate on the  
UPS back panel. Save the  
screws for reassembly.  
3. The card and slot are  
keyed to insert in one posi-  
tion only. Initially, the  
card should slide in freely  
as you carefully align  
screw holes. As you feel it  
click into place, press  
firmly to ensure solid seating in the slot.  
4. Using the screwdriver, secure the card to the UPS chassis with the  
two retaining screws. Make sure the screws are snug, not tight, to  
avoid damage to the device.  
2
 
CONFIGURATION  
Connect USB Cable  
Connect the Intellislot USB card to an available USB port on the com-  
puter using the included USB cable.  
Configure Power Management for Automated Shutdown  
1. Open the Power Options Properties window by clicking on Start,  
then Settings, Control Panel and, finally, Power Options.  
2. In the Power Options Properties window, select the Power Meter  
tab.  
a. Click on the Battery icon in the Power status window.  
Power  
Meter  
tab  
Battery  
icon  
3
     
b. The Detailed Battery information window appears. Verify the  
Battery Name is “USB Intellislot Card,” and the Manufacturer is  
“LIEBERT.”  
c. Click the OK button to return to the Power Options Properties  
window.  
Battery Name  
should  
be USB  
Intellislot  
Card  
Manufacturer  
should be  
LIEBERT  
4
3. In the Power Options Properties window, select the Alarms tab.  
4. Two alarms are available to perform automated OS shutdown: Low  
battery alarm and Critical battery alarm.  
An automated shutdown can be performed on either alarm.  
Alarms  
tab  
Alarm Action...  
buttons  
5. To enable automated shutdown for either alarm, select the associated  
Alarm Action button for the alarm you would like to configure.  
a. Enable the Alarm Action by checking the box next to “When the  
Alarm goes off, the computer will:”  
b. Select Shut Down from the drop down menu  
c. Click OK to save the changes and close the Alarm Action window.  
6. Click the Apply button on the Power Options Properties window,  
then click on the OK button to exit.  
5
PRODUCT WARRANTY REGISTRATION  
To register for warranty protection,  
• Visit the Quick Links section of our Web site at:  
www.liebert.com  
• Click on Product Warranty Registration and fill in the form.  
For any questions, please contact us at:  
US: (800) 222-5877  
Outside the US: (614) 841-6755  
[email protected]  
6
 
MONITORING  
IntelliSlot USB Card™  
USER MANUAL  
Technical Support/Service  
The Company Behind the Products  
Web Site  
www.liebert.com  
Monitoring  
800-222-5877  
With over a million installations around the globe,  
Liebert is the world leader in computer protection  
systems. Since its founding in 1965, Liebert has  
[email protected]  
Outside the US: 614-841-6755  
developed  
a
complete range of support and  
protection systems for sensitive electronics:  
Single-Phase UPS  
800-222-5877  
[email protected]  
•
•
•
Environmental systems—close-control air  
conditioning from 1 to 60 tons  
Power conditioning and UPS with power  
ranges from 300 VA to more than 1000 kVA  
Integrated systems that provide both  
Outside the US: 614-841-6755  
Three-Phase UPS  
800-543-2378  
[email protected]  
Environmental Systems  
environmental and power protection in  
single, flexible package  
a
800-543-2778  
Outside the United States  
•
•
Monitoring and control—from systems of any  
size or location, on-site or remote  
Service and support through more than 100  
service centers around the world and a 24/7  
Customer Response Center  
614-888-0246  
Locations  
United States  
1050 Dearborn Drive  
P.O. Box 29186  
Columbus, OH 43229  
While every precaution has been taken to ensure  
the accuracy and completeness of this literature,  
Liebert Corporation assumes no responsibility and  
disclaims all liability for damages resulting from use  
of this information or for any errors or omissions.  
Italy  
Via Leonardo Da Vinci 8  
Zona Industriale Tognana  
35028 Piove Di Sacco (PD)  
+39 049 9719 111  
Fax: +39 049 5841 257  
Asia  
23F, Allied Kajima Bldg.  
138 Gloucester Road  
Wanchai  
© 2003 Liebert Corporation  
All rights reserved throughout the world.  
Specifications subject to change without notice.  
Hong Kong  
+852 2 572 2201  
Fax: +852 2 831 0114  
® Liebert and the Liebert logo are registered  
trademarks of Liebert Corporation. All names  
referred to are trademarks or registered  
trademarks of their respective owners.  
SL-23220 (4/03) Rev. 0  

Nokia 3586i User Manual
Lenoxx Electronics SL 328 User Manual
HTC Touch Pro User Manual
HTC Shift User Manual
HP Hewlett Packard MAILBUS 400 User Manual
Hitachi Travelstar 0S03563 User Manual
EarthQuake 1692210 User Manual
Cypress CY7B9920 User Manual
Black & Decker DCM12WH User Manual
Aiwa CX NA30 User Manual